Levelit wedges are used together with spacer clips and installation pliers to bring adjacent tiles into perfect alignment. Made from durable polystyrene, they are highly wear-resistant and can be reused multiple times.
Technical specifications
| | | | |
Specifications | LEVELIT WEDGES – 100 PIECES | LEVELIT WEDGES – 250 PIECES | LEVELIT WEDGES – 500 PIECES |
Reference | TK100 | TK250 | TK500 |
EAN Code | 5430000539210 | 5430000539227 | 5430000539104 |
Compatible with | Levelit and XL Clips | Levelit and XL Clips | Levelit and XL Clips |
Packaging | 100 pieces | 250 pieces | 500 pieces |
Documents |
The reusable Levelit levelling wedges are an essential part of the Levelit tile levelling system. Used together with the spacer clips and levelling pliers, they keep adjacent tiles perfectly aligned at the same height while the adhesive cures. This prevents lippage and ensures a professional finish.
Manufactured from high-quality polystyrene, the wedges are designed for long-lasting, repeated use. Their large pressure surface distributes force evenly across the tile, ensuring precise levelling without damaging the surface. Once the adhesive has cured, the wedges can be easily removed and reused for future tiling projects.
Always apply sufficient tile adhesive and place the first tile. Check that the tile is perfectly level before continuing with the installation.
Slide the clip(s) underneath the tile and press the tile down gently. Place the next tile after installing the clips. Make sure the tile is positioned on top of the clip base.
Depending on the tile size, place one or more clips along each side. Tap the tile into place.
Slide the wedge through the opening of the clip. Use levelling pliers to push the wedge through the clip with sufficient force until the tiles are perfectly level.
Tip: Do not remove the wedge yet.
Leave the wedge in place for less than 24 hours after tightening. Once the tile adhesive is almost fully cured, the clip and wedge can be easily removed using a rubber mallet or your foot.
Tip: Always break the clip and wedge in the direction of the grout joint.
Remove the wedges from the clips. The wedges can be reused.
The number of clips and wedges required depends on several factors, including the tile size and the total area to be tiled. Refer to the consumption guide below to calculate the required quantity.
Step 1Measure the length and width of your tile. Then locate these dimensions in the consumption chart alongside. The point where the two measurements intersect indicates the number of clips required per m2.
Calculate the total area to be tiled in m² by multiplying the length by the width of the area.
Multiply the number of clips required per m2 (from Step 1) by the total area to be tiled (from Step 2). This gives you the total number of clips required for your project.
| | | | |
Specifications | LEVELIT WEDGES – 100 PIECES | LEVELIT WEDGES – 250 PIECES | LEVELIT WEDGES – 500 PIECES |
Reference | TK100 | TK250 | TK500 |
EAN Code | 5430000539210 | 5430000539227 | 5430000539104 |
Compatible with | Levelit and XL Clips | Levelit and XL Clips | Levelit and XL Clips |
Packaging | 100 pieces | 250 pieces | 500 pieces |
Documents |
The reusable Levelit levelling wedges are an essential part of the Levelit tile levelling system. Used together with the spacer clips and levelling pliers, they keep adjacent tiles perfectly aligned at the same height while the adhesive cures. This prevents lippage and ensures a professional finish.
Manufactured from high-quality polystyrene, the wedges are designed for long-lasting, repeated use. Their large pressure surface distributes force evenly across the tile, ensuring precise levelling without damaging the surface. Once the adhesive has cured, the wedges can be easily removed and reused for future tiling projects.
Always apply sufficient tile adhesive and place the first tile. Check that the tile is perfectly level before continuing with the installation.
Slide the clip(s) underneath the tile and press the tile down gently. Place the next tile after installing the clips. Make sure the tile is positioned on top of the clip base.
Depending on the tile size, place one or more clips along each side. Tap the tile into place.
Slide the wedge through the opening of the clip. Use levelling pliers to push the wedge through the clip with sufficient force until the tiles are perfectly level.
Tip: Do not remove the wedge yet.
Leave the wedge in place for less than 24 hours after tightening. Once the tile adhesive is almost fully cured, the clip and wedge can be easily removed using a rubber mallet or your foot.
Tip: Always break the clip and wedge in the direction of the grout joint.
Remove the wedges from the clips. The wedges can be reused.
The number of clips and wedges required depends on several factors, including the tile size and the total area to be tiled. Refer to the consumption guide below to calculate the required quantity.
Step 1Measure the length and width of your tile. Then locate these dimensions in the consumption chart alongside. The point where the two measurements intersect indicates the number of clips required per m2.
Calculate the total area to be tiled in m² by multiplying the length by the width of the area.
Multiply the number of clips required per m2 (from Step 1) by the total area to be tiled (from Step 2). This gives you the total number of clips required for your project.
