The HELIX XL Starter Kit contains everything you need to start using the HELIX Tile Levelling System straight away. The complete kit includes HELIX XL Long Spacer Clips and reusable Twist Caps, all conveniently packed in a durable, reusable bucket.
Technical specifications
| | |
Specifications | HELIX LONG STARTER KIT 2L MM – 200 PCS |
Reference | SET200-2L |
EAN code | 5430003605196 |
Joint width | 2 mm |
Quantity | 200 pcs |
Tile thickness | 15 - 25 mm |
Documents | Data sheet |
With the HELIX XL Starter Kit, you have everything you need to start installing thick wall and floor tiles straight away. The kit includes HELIX Long Spacer Clips and reusable Twist Caps, providing everything you need to achieve a perfectly level finish without any additional purchases.
HELIX Long Spacer Clips ensure precise alignment of adjacent tiles while maintaining consistent joint widths. Used together with the reusable Twist Caps, they eliminate lippage and keep the tiles securely in place as the adhesive cures. The simple twist mechanism allows pressure to be adjusted quickly and accurately for precise installation.
Designed for tiles 15–25 mm thick, the HELIX XL Starter Kit is ideal for installing thick wall and floor tiles, large-format tiles and natural stone. The durable, reusable bucket keeps all components neatly organised, making storage, transport and use on site quick and convenient.
Always apply sufficient tile adhesive and place the first tile. Check that the tile is perfectly level before continuing.
Slide the clip(s) underneath the tile and press the tile down gently. Place the next tile after positioning the clips. Make sure the tile is placed on top of the clip base. Depending on the tile size, place one or more clips along each side. Tap the tile into position.
Turn the cap onto the clip and tighten it firmly.
Tip: Do not remove the cap yet.
Leave the cap in place for less than 24 hours after tightening. Once the tile adhesive is ALMOST fully cured, the clip and cap can be easily removed using a rubber mallet or your foot.
Tip: Always break the clip and cap in the direction of the grout joint.
Remove the caps from the clips. The caps can be reused.
The number of clips and wedges required depends on several factors, including the tile size and the total area to be tiled. Refer to the consumption guide below to calculate the required quantity.
Step 1Measure the length and width of your tile. Then locate these dimensions in the consumption chart alongside. The point where the two measurements intersect indicates the number of clips required per m2.
Calculate the total area to be tiled in m² by multiplying the length by the width of the area.
Multiply the number of clips required per m2 (from Step 1) by the total area to be tiled (from Step 2). This gives you the total number of clips required for your project.
| | |
Specifications | HELIX LONG STARTER KIT 2L MM – 200 PCS |
Reference | SET200-2L |
EAN code | 5430003605196 |
Joint width | 2 mm |
Quantity | 200 pcs |
Tile thickness | 15 - 25 mm |
Documents | Data sheet |
With the HELIX XL Starter Kit, you have everything you need to start installing thick wall and floor tiles straight away. The kit includes HELIX Long Spacer Clips and reusable Twist Caps, providing everything you need to achieve a perfectly level finish without any additional purchases.
HELIX Long Spacer Clips ensure precise alignment of adjacent tiles while maintaining consistent joint widths. Used together with the reusable Twist Caps, they eliminate lippage and keep the tiles securely in place as the adhesive cures. The simple twist mechanism allows pressure to be adjusted quickly and accurately for precise installation.
Designed for tiles 15–25 mm thick, the HELIX XL Starter Kit is ideal for installing thick wall and floor tiles, large-format tiles and natural stone. The durable, reusable bucket keeps all components neatly organised, making storage, transport and use on site quick and convenient.
Always apply sufficient tile adhesive and place the first tile. Check that the tile is perfectly level before continuing.
Slide the clip(s) underneath the tile and press the tile down gently. Place the next tile after positioning the clips. Make sure the tile is placed on top of the clip base. Depending on the tile size, place one or more clips along each side. Tap the tile into position.
Turn the cap onto the clip and tighten it firmly.
Tip: Do not remove the cap yet.
Leave the cap in place for less than 24 hours after tightening. Once the tile adhesive is ALMOST fully cured, the clip and cap can be easily removed using a rubber mallet or your foot.
Tip: Always break the clip and cap in the direction of the grout joint.
Remove the caps from the clips. The caps can be reused.
The number of clips and wedges required depends on several factors, including the tile size and the total area to be tiled. Refer to the consumption guide below to calculate the required quantity.
Step 1Measure the length and width of your tile. Then locate these dimensions in the consumption chart alongside. The point where the two measurements intersect indicates the number of clips required per m2.
Calculate the total area to be tiled in m² by multiplying the length by the width of the area.
Multiply the number of clips required per m2 (from Step 1) by the total area to be tiled (from Step 2). This gives you the total number of clips required for your project.
